一、自上料攪拌車攪拌軸停止轉動的原因：在生產過程中當出現混凝土自上料攪拌車攪拌軸停止轉動或是轉動有點緩慢都是正?，F(xiàn)象，如果這種情況首先停機檢查，看看有沒有出現下列三種情況。

1、 Reasons for stopping the rotation of the mixing shaft of the self loading mixer: it is normal that the mixing shaft of the concrete self loading mixer stops rotating or rotates a little slowly during the production process. If this is the case, first stop the machine and check to see if the following three situations occur.

1、電機傳動皮帶有沒有出現松動的情況？自拌混凝土攪拌車電機傳動皮帶過松也能導致商品混凝土拌合機攪拌軸轉動緩慢或者停止轉動，電機傳動皮帶過松，導致傳遞的動力不足。

1. Is the motor drive belt loose? The loose motor drive belt of the self mixing concrete mixer can also cause the mixing shaft of the commercial concrete mixer to rotate slowly or stop rotating. The loose motor drive belt will lead to insufficient power transmission.

2、有沒有嚴重超載？自拌混凝土攪拌車攪拌軸如果超過正常工作負荷，會使攪拌軸轉動緩慢，若負荷過大，就會導致攪拌軸停轉或者是攪拌軸彎曲。

2. Is there a serious overload? If the mixing shaft of the self mixing concrete mixer exceeds the normal working load, the mixing shaft will rotate slowly. If the load is too large, the mixing shaft will stop or the mixing shaft will be bent.

3、攪拌葉片或側葉片與筒體內壁間有沒有大的異物？出現這種情況也會使混凝土自動上料攪拌車攪拌軸停止轉動或轉動緩慢。攪拌葉片或側葉片與罐內壁間有較大的異物也會導致攪拌軸停轉，之所以能卡存異物，就是由于攪拌葉片或側葉片與罐內壁間隙過大造成的，尤其是石子。

3. Is there any large foreign matter between the mixing blade or side blade and the inner wall of the cylinder? This situation will also make the mixing shaft of the automatic concrete feeding mixer stop rotating or rotate slowly. There are large foreign matters between the mixing blade or side blade and the inner wall of the tank, which will also lead to the stop of the mixing shaft. The reason why foreign matters can be stuck is due to the excessive gap between the mixing blade or side blade and the inner wall of the tank, especially stones.

二、自上料攪拌車攪拌軸停轉的解決方法

2、 Solution to stopping of mixing shaft of self loading mixer

1、混凝土自動上料攪拌車電機傳動皮帶過松的情況，只需停機后調整混凝土攪拌機電機傳動皮帶的張緊度即可。

1. When the motor driving belt of the concrete automatic feeding mixer is too loose, the tension of the driving belt of the concrete mixer should be adjusted after stopping.

2、混凝土自動上料攪拌車超載而造成攪拌軸停轉，只需調整進料量，卸出多余的物料，降低攪拌軸轉動負荷即可。

2. If the automatic concrete loading mixer truck is overloaded and the mixing shaft stops running, just adjust the feeding amount, unload the excess materials and reduce the rotating load of the mixing shaft.

3、側葉片與關內壁卡滯物料時，在攪拌軸停轉前往往會有尖銳刺耳的摩擦聲，出現這種情況時，需立即停機檢查，人工排除異物，重新調整混凝土自動上料攪拌車攪拌葉片或側葉片與罐內壁間的間隙，有必要時可以用水先清洗下。

3. When the side blade is stuck with the inner wall of the tank, there is often a sharp and harsh friction sound before the mixing shaft stops. In this case, it is necessary to stop the machine immediately for inspection, manually eliminate foreign matters, readjust the gap between the mixing blade of the automatic concrete loading mixer or the side blade and the inner wall of the tank, and clean it with water if necessary.

三、自動上料攪拌車使用中要注意的問題

3、 Problems needing attention in the use of automatic feeding mixer

1、自動上料攪拌車應停入在平地上，并將鏟斗平放地面。當發動機熄火后，需反復多次扳動工作裝置操縱手柄，確保各液壓缸處于無壓休息狀態。當自動上料攪拌車只能停在坡道上時，要將輪胎墊牢。

1. The automatic loading mixer truck shall stop on the flat ground and place the bucket flat on the ground. After the engine is shut down, the operating handle of the working device shall be pulled repeatedly to ensure that each hydraulic cylinder is in a pressure free rest state. When the automatic loading mixer can only stop on the ramp, the tires shall be padded firmly.

2、自動上料攪拌車在停止工作后操作人員將各種手柄置于空擋或中間位置。

2. After the automatic feeding mixer stops working, the operator puts various handles in neutral or middle positions.

3、先取走電鎖鑰匙，然后關閉電源總開關，關閉門窗。

3. First remove the electric lock key, then turn off the main power switch, and finally close the doors and windows.

4、自動上料攪拌車嚴禁停在有明火或高溫地區，以防輪胎受熱爆炸，引起事故。

4. The automatic feeding mixer is strictly prohibited to stop in areas with open fire or high temperature, so as to prevent accidents caused by tire heating and explosion.

5、利用組合閥或儲氣罐對輪胎進行充氣時，人不得站在自動上料攪拌車輪胎的正面，以防爆炸傷人。

5. When using the combined valve or air tank to inflate the tire, people shall not stand in the front of the tire of the automatic feeding mixer to prevent explosion injury.